Are you having water heater problems? No need to worry – we’ve got all the top tips you need in this blog! From reducing the temperature to checking the anode rod, we’ll cover everything you need to know to get your water heater up and running again as quickly and efficiently as possible. So whether you’re experiencing a malfunction or want to keep your tank water hot and fresh, read on for our top water heater repair tips!
Reduce the temperature
Water heaters can be a nuisance in the summertime. Not only are they hot to the touch, but they can also cause problems like water leakage and water heater failure. To reduce the temperature of your water heater and prevent these issues from happening.
In addition, try to schedule your water heater servicing during the more excellent parts of the day. Approaching water heater repair in hot weather can be dangerous, so always consult a professional before beginning any plumbing work. More homeowners are using water heaters with controls that allow them to set a lower temperature in the evening or at night instead of during the day.
Check fluid levels and replace them as needed.
One of the most common water heater repairs is checking for leaks and replacing lost or broken hoses. Make sure your tank water level is high enough by adding additional fresh water if necessary, then check for leaks around plumbing joints, Columbian tubes (if present), valves, fittings, and elsewhere. If you notice any signs of leakage, be prepared to add stop-leak caulk around those areas as soon as possible.
Over time, water heater parts can wear down and deteriorate, which can cause them to fail faster. Inspect all water heater components at least once a year and replace any worn or damaged parts as needed.
Check your anode rod.
One of the most common causes of water heater failure is an anode rod not working correctly. An anode rod is a metal pipe that sits in the tank near the bottom and helps create hot gas used to heat water in the heating element. If it becomes misshapen or corroded, this will reduce the water heating element’s efficiency, and over time the rod can break, leading to a water heater failure.
Check your water heater’s anode rod at least once a year by removing the cover plate and looking for visible signs of wear or corrosion. If you see any problems, replace the anode rod as soon as possible.
Clean pilot light
In most cases, a dirty or clogged pilot light will prevent your hot water from coming on. A clean pilot light means there’s sufficient gas being fed to the heating element, but it can also be caused by blocked air vents (below), so it’s always a good idea to check these before calling for service.
If the pilot light is dirty, try using a pipe cleaner or an electric water heater starter kit to clear the obstruction. Otherwise, you may need to call in a professional plumber.
Occasionally inspect
Water heaters are essential to any home, and it’s important to keep them in good condition. Inspect them occasionally and get them repaired if there are any signs of wear or damage. Always call a professional if you notice anything suspicious. In an emergency, water heaters can’t handle extreme weather conditions, so be safe and keep them in good condition by regularly inspecting them.
Drain water heater annually
Keeping your water heater in good condition is essential for its long-term performance. One of the most important things you can do is drain the water heater yearly. This will remove any accumulated sediment and dirt, which can reduce its efficiency over time.
It would be best if you also replaced the gasket on the bottom of the water heater every year. If you notice any unusual noises or smells coming from your water heater, please don’t hesitate to call a professional. By following these simple tips, you can ensure your water heater is functioning at its best and ready to tackle the next hot summer day!
Monitor the temperature and pressure relief valve
Water heater repair can be daunting, but with the right tips and guidance, it can be a relatively straightforward process. One of the most important things to monitor is the temperature and pressure relief valve. If there are any issues, have them fixed as soon as possible to avoid water damage and costly repairs.
Additionally, keep an eye out for rust or fungus on iron parts, which could indicate a leaky tank or pump unit. Always wear safety goggles, a suit, and rubber gloves when working on water heater repairs.
Switch to the metal inlet and output pipes from plastic ones
It’s time to switch to the metal inlet and output pipes for water heaters over ten years old. This is because plastic pipes are notorious for leaking and can cause electrical problems. First, disconnect the electric supply line from the water heater to make the switch.
Next, unscrew the existing copper pipe connections and use new fittings for metal plumbing systems. Once you have replaced the pipes, reconnect the electric supply line and test the water heater to ensure the installation was successful.
Tank Insulation
Keeping your water heater in top working condition is essential for your comfort and the safety of those around you. One of the most common repairs water heater owners make is tank insulation. This repair helps protect the water heater from cold weather and dampness damage.
It also keeps pipes warm, which reduces the chance of freezing or bursting during a freeze-up event. You’ll save money in the long run by doing this repair yourself! So, don’t wait – call a water heater repair technician today and get started on protecting your home and family!
Check the anode rod within the tank.
Water heater repair can be complicated and dangerous, so it’s essential to know the basics. One of the most important things to check is the anode rod within the water heater tank – this helps rid the water of contaminants by exchanging electrons with the air.
If contamination levels are high, this can lead to the degradation of equipment and increased risk of fire. Wear gloves and eye protection to avoid contact with chemicals when checking or replacing the anode rod. Finally, always contact a professional plumber for prompt and efficient water heater repair.
Air intake filter replacement
If you’re noticing a strange noise coming from your water heater, it’s likely because of an air intake filter that needs to be replaced. This is a relatively easy task for those with basic mechanical skills – remove the filter and replace it with a new one. Ensure the air intake filters are cleaned regularly to maintain good airflow into the water heater.
If you notice any yellowing or discoloration on the exterior of your water heater, it may be time for a replacement. So, keep these top 10 water heater repair tips in mind, and you’ll be on your way to a water heater that’s running like new again!
Keep an eye on electrical connections.
Water heaters can be a major headache if something goes wrong. That’s why keeping an eye on electrical connections, water heater insulation, and plumbing is essential. Ensure all electrical connections are tight and free of corrosion and check for frayed or damaged wiring.
If you find any signs of trouble, don’t hesitate to replace faulty components or install a new water heater. Cleaning your water heater regularly will help prevent the build-up of dead skin cells, mold, and bacteria. So, whatever water heater repair tips you need, check out our blog!
Conclusion
When it comes to water heater repairs, it’s always essential to follow these top repair tips to ensure a smooth and trouble-free experience. By regularly inspecting the water heater, draining it, and replacing filters and anodes, you’ll keep your home heating system running smoothly. In addition, make sure to consult with a professional if you notice any unusual symptoms or problems. At Furnace Fellas in Calgary, Alberta, we know how important it is to stay in tune with water heater repair, and we’re here to help. Contact us today at 403-899-0982 to learn more!
